PURPOSE AND POLICY
The purpose of the RETERM - Thermal Engineering
Journal is to publish papers of permanent interest dealing
with research, development and design related to Energy, Equipments,
Oil and Gas.
The journal is divided in two sections: i) Technology
and ii) Science. The Technology section comprises articles
that document modern engineering applications or general advances
in industry. The Science section is intended for publishing
articles that deal with fundamental advances in heat transfer
and fluid mechanics, new physical insights, and novel experimental
and analytical methods that have great appeal for the industry
Submission of full-length scientific, review
or technical papers to RETERM implies that it is not under
consideration for publication elsewhere and it has not been
previously published. Exception is made for papers previously
published in proceedings of conferences. Review articles should
constitute a critical appraisal of published information.
The decision of acceptance for publication either
for the Technology or the Science section lies with the Editors
and is based on the recommendations of at least two independent
referees and of the Editorial Board, if necessary.
All manuscripts for RETERM must be written in
clear and concise English. The submission of a manuscript
may be carried out by:
a) E-mail: The file (Word for Windows or Latex)
with the full manuscript (including figures) should be sent
b) Mail: Three (3) hard copies of the manuscript
should be sent to the Technical Editor at: RETERM –
Departamento de Engenharia Mecânica - Universidade Federal
do Paraná, Centro Politécnico, Caixa Postal
19011, CEP 81531-990, Curitiba/PR-Brasil, or
c) On-line: Follow all instructions (in Portuguese)
as detailed at http://calvados.c3sl.ufpr.br/reterm/. Upon
registering, the submission procedure becomes available to
In any case, the manuscript should be accompanied
by a cover letter indicating to which journal section the
paper is intended to, i.e. Technology or Science. The cover
letter should also contain the full name and postal address
of the corresponding author and his/her phone, fax number
and e-mail address.
If the authors so wish, the names of up to five
persons who could act as referees may be indicated.
The authors should retain a copy of their manuscript
since the journal cannot accept responsibility for damage
or loss of papers.
The manuscript should be organized in the following
order: Title, authors, affiliations, abstract, keywords (3
to 5), nomenclature, main text (divided into sections and
subsections), acknowledgements, references, and appendices.
The tables and captions, as well as figures and captions should
be appropriately distributed into the main text.
The abstract should state the objectives, methodology
and main conclusions in up to 300 words. In all papers, sufficient
information should be provided in the text or by referring
to papers in other journals, to permit the work to be repeated.
Manuscripts should be typed according to the
template file available on the journal internet site: http://demec.ufpr.br/reterm/autores/index.htm.
The pages should be numbered and the full length of the manuscript
including tables and figures should not exceed 10 pages.
Units and Symbols
The use of SI (metric) system is mandatory for
all reported data. Temperatures should be given in °C
or K. Uncertainties should be specified for experimental and
The nomenclature section should list, in alphabetical
order, all used symbols and their definitions, followed by,
if applicable, Greek symbols, subscripts and superscripts.
Besides, all symbols should be defined within the text.
Mathematical expressions should be produced
by an equation editor and should not be introduced along the
text itself, as part of a sentence line, but typed on individual
Numbers that identify mathematical expressions
should be enclosed in parentheses located at the right margin
of the paragraph. Refer to equations in the text such as in
“…as derived from eq. (1)…”, or, if
at the beginning of a sentence, “Equation (1) indicates…”.
Figures and Tables
Photographs, charts and diagrams are all to
be referred to as “Figure (s)”.
Figures should be submitted in laser printer
output, original line drawings or glossy prints. Photocopies
should be avoided.
Figures should be clear and suitable for reduction
(up to 50%). The amount of lettering should be reduced as
much as possible by transferring it to the figure legend.
Remaining lettering should be large enough to be clearly legible.
Figures and tables, with a suitable caption,
should be numbered consecutively in the order in which they
are referred to in the main text. Footnotes to tables should
be typed below the table and should be referred to by superscript
Refer to figures or tables in the text such
as in “Figure 1 shows…”, or, “…in
Fig. 1 it is shown…”.
Please note that color figures or tables cannot
be printed in color. However, they will appear in color in
the journal website.
Cite references in the text by giving the last
name of the author(s) and the year of publication: either
“Recent work (Prata and Parise, 1985) has indicated...”
or “Recently Prata and Parise (1985) indicated....”.
With three or more authors, use the form “Prata et al.
(1985)…”. When two or more references have the
same text identification, append “a”, “b”,
etc, to the year of publication.
Acceptable references include: journal articles,
dissertations, published conference proceedings, books, accepted
articles if the journal is identified, and private communications.
References cited in the text should be listed,
in alphabetical order of the last name of the first author,
at the end of the paper. Some sample references follow:
Kays, W. M., and London, A. L., 1964, Compact
Heat Exchangers, McGraw-Hill Book Company. (for books)
Mengüç, M. P., and Dutta, P., 1994,
Scattering Tomography and its Application to Sooting Diffusion
Flames, Journal of Heat Transfer, Vol. 116, No. 1, pp. 144-151.
(for journal articles)
Phiney, L. M., 1997, Electronic Desorption
and Microstructure Adhesion Reduction Using Ultrashort-Pulse
Lasers, Doctoral Thesis, University of California, Berkeley,
CA. (for theses)
Viskanta, R., 1995, Convective Heat Transfer
in Consolidated Porous Media: A Perspective, in: Symposium
on Thermal Science and Engineering in Honor of Chancellor
Chang-Lin Tien, University of California, Berkeley, pp.
43-50. (for conference proceedings)
Upon notification of acceptance, authors should
submit an electronic copy (Word for Windows, or Latex) of
the final corrected version of their paper via e-mail (firstname.lastname@example.org).
The formatting of the final paper should follow the RETERM
publication standard template, which may be downloaded from
the journal website http://demec.ufpr.br/reterm/autores/index.htm.
Please note that accepted papers which exceed
the standard length of eight journal pages will be subjected
to an excess-page charge of US$ 50.00 per page for each page
over eight pages. This charge will be invoiced to the author's
company, institute, or agency, as indicated.
One journal printed issue wiil be sent to the
first author of the paper free of charge. Additional printed
issues can be ordered from RETERM (email@example.com,
tel. (41) 3361-3124 or fax (41) 3361-3131) and will be charged
according to: 25 extra volumes (US$ 100.00) or 50 extra volumes
For inquiries related to the submission of articles
(including electronic submission), the status of accepted
articles or other inquiries, please contact RETERM at firstname.lastname@example.org.
The authors, or the first author on behalf of
all authors, must sign the “Copyright Transfer”
agreement before the article can be published. This transfer
agreement enables RETERM to protect the copyrighted material
for the authors, without the author relinquishing his/her
The copyright transfer covers the exclusive
rights to reproduce and distribute the article, including
reprints. Authors are responsible for obtaining from the copyright
holder permission to reproduce any material for which copyright